Bestop Rear Window Teeth Not Lining Up

As others have noted the bottom of the rear window bar does not seal against the rear door.

Bestop rear window teeth not lining up. Remove the metal Tailgate Bar from the bottom of the Rear Window and set it aside. To the top on each side of the rear window opening. 11203-00 which safely cleans and protects vinyl windows and helps prevent UV damage. Snap the Elastic Garters to the snaps on the Rear Bow above the rear window opening.

Cracks caused by misuse in cold temperatures are not covered under warranty. Not having the bar handy ifwhen you need to close the rear window in a rain storm unless you always tote it around with you. The windows become stiff and will crack. Rear Window Pull fl ap over to cover zipper and tuck in Secure Rear Window Flaps View from inside top.

The bar has a C shaped channel when viewed from the end. Install Elastic Garters Snap Elastic Garters to Rear Bow Remove the Rear Window from the box and lay it fl at with the backing side up. Several times I have caught myself forgetting to close the rear sliding window after using the Sunrider or unable to open the rear sliding window while flipping. Reach in under the Quarter Window opening and carefully slide the Rear Bow up on the Front Bow to increase the tension on the top.

Pull up on the lever and then down and out to release the hook from the loop in the windshield frame. The snap placement on the top is the same as the original top. Windshield Drivers Side of Vehicle Make sure space between top fabric and windshield fl ange is equal on both sides For best possible installation check to make sure that the soft top is perfectly. DO NOT roll the sides or rear window in cold weather.

Horizontal Rod Bracket. The sole supplier of factory soft tops on Jeep Wrangler since 1986. Have rear window extended as low as possible to line up with front side windows and for better rear visibility. Set the hook but do not lock the latch.

C 0611 56820 pg. I think Bestop remedied this from earlier reviews by including a gasketseal that goes over the rear door of the Jeep but it still is not a complete seal. Then the pin may be inserted into a higher hole position. Snap the two short straps to the snaps in the rear bow and buckle the straps to the footman loops on the rear corners of the vehicle.

View from Rear Vertical Rod Side Belt Retainer Install Vertical Rod Place the end of the Horizontal Rod against the outside of the Horizontal Rod Bracket on the windshield frame. Line up the hole in the rod with the hole in the bracket and install a 516 x 34 Hex Bolt with a Wing Nut to the inside of the vehicle. More to the rear window. 11206-00 will help prevent damage and keep the zippers in smooth working condition.

This will allow the snaps to line up more easily. If the snaps dont appear to line up push the rear bow forward to relieve the pressure on the bow. Release the latch that secures the header to the windshield. I know for a fact that the rear window on the Smittybilt replacement top that was on my TJ when I bought it and the Bestop Replace-A-Top I put on two months later had different sized rear windows not by much but more importantly the size and count of the zipper teeth were different.

11203-00 which safely cleans and. Release the plastic strip from the retainer along the bottom and front of the panel To roll up the Rear Window remove the Tailgate Bar and open the zippers on each side of the window to the top. Locate the Tailgate Bar set aside in Step One. Rear Window Remove the Quarter Panels and the Rear Win-dow.

Line up the center drill hole in the fabric with the center notch in the header. Bestop recommends Bestop Vinyl Window Cleaner part no. Plus the window tends to sag a bit in the center when its rolled up. Line it up and slide it across.

Leader in Jeep truck accessories for 60 years. If you already have holes that line up skip to Step 5. Snap the Elastic Garters to the snaps on the Rear Bow above the rear window opening. Close the sunroof and secure the header latch.

I understand top of canopy is narrower sides slanting inwards as you go up so it can be folded into the bed but it would look better if the sides were. You wont stretch out the elastic rear window straps as quickly because that bar adds a good deal of weight to what youre rolling up. Insert the pin in the slide into the lowest of the three holes in the Front Bow. The Rear Window should be rolled up and secured with the Inside the top locate the fl aps sewn elastic garters for proper ventilation.

However due to the installation variances fabric stretch and manufacturing tolerances it is possible that some of the snaps will not line up exactly. Remove Quarter Windows and Rear Window. Then hold up the top of the window with one hand. Use masking tape to.

The rear sliding window is perfect to control this as rear passengers might not want the side windows down and wind in their face and I use the Sunrider even when it is quite cool. Once the zipper is caught start the top slider 12. To roll up the Rear Window remove the Tailgate Bar and open the zippers on each side of the. Customize your Jeep online today.

Pull the fl aps over to cover the zipper and tuck them in. The top will loosen up after a few hours in the sun. Remove the Quarter Windows and the Rear Window. Rear Bow Front Bow.

Bestop recommends Bestop Vinyl Window Cleaner part no. Install Elastic Garters Snap Elastic Garters to Rear Bow To start the zipper pull the two sliders as far down as possible on the drivers side of the window in order to catch the sliders to the pin. Rear Window Qty - 1 8 x 12 Pan Head Washer Screw - Black Qty - 4 Part. To remove the Quarter Windows release the hook and loop and unzip the rear and top zippers.

Install Rear Window a.

If you re looking for Bestop Rear Window Teeth Not Lining Up you've reached the ideal place. We ve got 15 images about bestop rear window teeth not lining up including images, pictures, photos, backgrounds, and more. In these web page, we additionally provide variety of graphics available. Such as png, jpg, animated gifs, pic art, logo, blackandwhite, transparent, etc