How To Apply Window Tint To Rear Window

Window Tint regulations vary per state and country.

How to apply window tint to rear window. To apply and generally gives a better result on windows that are curved. Cut the section off with a razor blade or precision knife. Once youve applied the tint grab some warm water in a bottle and spray the window. Tint just the lower portion of it so that the top roof part is not tinted as it already has the Tesla factory tint.

Skulleyb January 12 2018. Cut the Window Tint to Fit Your Windows Wet the outside of the window with the application solution. Cut the tint film 1 inch longer than the height of the window. Place your tint onto the outside rear window surface with the transparent plastic sheet facing outwards.

Get it on there really nicely. Remember that the tint film goes on the inside of the window so check that the film fits properly since the outside and inside window seals are sometimes different. Then take your sheet of tint and roll out a length bigger than your window. Squeegee the film onto the window pushing bubbles out to the edges.

Spray a little bit of soap and water on to it and go ahead and smear the window with the actual fabric softener. Slip the bottom of the film underneath the window gasket. The sharper the blade the sharper the finish. Window tint for cars.

Fit the piece of film to your window. Please review and research local regulations prior to purchase and use of this product. Cut the tint film with a razor knife to get a sharp edge. Secure the Black Magic window tint film to the frame with masking tape.

In order to get that perfect looking tint on your windows you will need the following. Squeegee top of the film to the glass. Tape the window tint film securely in place with the scotch tape. FOR USE ON GLASS WINDOWS ONLY inside surface DO NOT apply to plastic or plexiglass windows.

Whomever has to apply tint film to that entire rear window will curse your name until the end of time though they will take your money anyway. Mine was done in two pieces. You want to ease it on from the edges to avoid any bubbles. Use your Blue Max Squeegee start from the middle of the actual window and work your way outward.

Tint the entire rear window glass. Spray the outside of the back window lightly with soap solution and lay the film on the outside of the rear windscreen with the clear backing side facing you. The rest of the film should overlap on the sides and bottom. Then taking your time start applying the tint inch by inch starting at the bottom.

Part one of the DSTV Mazda RX-8 Proj. Next spray the outside of your window with soapy water. Roll the film liner side facing out onto the glass keeping in mind that the tint will be applied to the interior side of the glass. They used the antenna line to hide the seam.

First two items that you need is your water bottle and a bounty fabric softener. ITs perfect you cannot see it at all form the outside only only a small bit inside. It may look ugly. Press gently down on the film to temporarily hold it in place for trimming.

Trim film to a rough size using the exterior of rear window as template Unroll the window film identifying the backing liner from the tint film side. Film Application Solution. In todays segment of Tint Your Ride I am going to show you how to apply and dry shrink a rear window. Please note that when you separate the tint from the transparent sheet unless your fingers are wet permanent fingerprints can be left on the glue surface of the tint.

Cut the tint film 1 inch wider than the width of the window. Tinting the windows of your car truck or SUV can add style and comfort to your driving experience as well as helping you protect your interior from light. Press firmly on squeegee to remove ALL. This will show a line where the edge of the tint is.

Try to keep your fingers moist when handling tint. PolyFilm assumes no responsibility for misuse illegal or improper application of this window tint. On this episode of Driving Sports TV we show you how to install window film to improve security and comfort in any car. On curved glass squeegee from the center to the bottom then squeegee film toward the sides.

First put the application spray on the window youre about to tint. Stick the film to the windows interior leaving 18 to ¼ inch 3 to 6 centimeters at the top of the window. With the window rolled down a couple inches line the top edge of the window tint film up with the top of the glass. Also known as tint slime when added to water gives you a soapy solution essential for applying your window tint.

To install window tints first clean the window youre tinting with soapy water and scrape away any dust lint and adhesive on it with a razor blade. OK there are 2 ways to tint the rear window.

If you re searching for How To Apply Window Tint To Rear Window you've arrived at the ideal place. We have 30 images about how to apply window tint to rear window including images, pictures, photos, backgrounds, and more. In such page, we also provide variety of graphics out there. Such as png, jpg, animated gifs, pic art, logo, blackandwhite, transparent, etc